Pro-95 Cheat Sheet 

Programming
         Storing known non trunked frequencies
1.Press Manual, Press three digits to get the bank and channel number desired then Press Manual again.  (upper left should read Mxxx for your bank and channel number)
         2. Press PGM, (upper left should change from M to P) 
3. Enter the frequency using the numbered keys in the format xx.xxxxx, xxx.xxxxx or xxxx.xxxxx.  
         4. If needed, Press Mode to change the receiver mode.
         5. Press Enter. 
6. Press PGM and repeat steps 3, 4 and 5 then step 6 again until all desired frequencies are entered in selected bank.
         
         Storing known trunked frequencies
1.Press Manual, Press three digits to get the bank and channel number desired then Press Manual again.  (upper left should read Mxxx for your bank and channel number)
         2. Press Trunk
         3. Press Mode for MOT (Motorola) or ED (EDACS).
         4. Press PGM
         5. Enter the frequency
         6. Press Enter  
         7. Repeat steps 3 through 6 until all frequencies are entered in selected bank.
Note:  	1. EDACS must start in channel 01 of bank not channel 00, and must 
       	follow a listed order.
           
         2. Motorola needs only the control channels entered.

         Storing Text Tags
1.Press Manual, Press three digits to get the bank and channel number desired then Press Manual again.  (upper left should read Mxxx for your bank and channel number)
         2. Press PGM, (upper left should change from M to P)
         3. Press Text, the cursor appears on line 3.
4. Using the numbered keys text in the line up to 12 characters.  The letters above each number will help in the selection.  Example, POLICE DISP (11 characters counting the space) The first letter is P, Press the number 7 then the number 1 for P. (7 will open the four numbers PQRS and by selecting 1 is for the first of these four.  A 7 then 2 would get the letter Q.  Press up of down to move the courser back an fourth or to correct a mistake.
		5. Press Enter
			Note: Chart on page 31 for other text options.

Scanning Banks 

         Turn Radio on, the last bank(s) selected will start scanning.  
Note: If the radio was in search mode when turned off, the radio will continue that search pattern when turned on until Scan or manual is pressed.

To change scanning banks. 
1. Press the number associated with desired bank.  The number on top line of display will either be on or off accordingly. 

         
         
         
         
         
         To change from Open Mode to Closed Mode (or the reverse).
1. Press Manual then the bank and number you want to change.
2. Press FUNC then 5 (Bank Open of Bank Closed will display).
3. Alternately, while scanning in a bank, when the radio stops on a call, Press FUNC then 5 (Bank open or Bank Closed will display). 
Note: In the Open Mode the scanner will stop on any transmission of all talk groups in a system.  In the Closed Mode the scanner will stop on only unlocked stored ID’s.

Talk Group ID’s
         These are Identification assigned by the manager of the system you desire to scan.
         
         Storing unknown ID’s
1. When the scanner stops on a conversion, Press Trunk, the bottom line will indicate where the ID is saved as x-xx, where the first x is the sub-bank number in the bank and the xx is the the number of ID’s 00 to 19 in the sub-bank.  
Note: 
1. Each bank has five 20 ID positions for a total of 100 per bank.  
2. If an ID was already stored, the bottom line will display ID was saved.
	Storing Known ID’s
1. Select out all banks except desired bank ie. While scanning press each numbered bank to deselect it except your desired bank.
 2. Press PGM.
3. Press Trunk.
4. Press down until bank 0-0  on appears at the top with Id no. 00 on the second line.
         5. Press mode, if needed for MOT or ED.
6. Enter the ID number, if necessary use the period for a hyphen.
7. Press Enter.
8. Press up and repeat 6, 7 and 8 until all are entered.